If the filter just sits in a well behind a hole in the wall your life is much easier. Reply With Quote 05-15-2016,10:02 AM #15 Flmarcus View Profile View Forum Posts View Articles Join Date May 2016 Location FL Posts 1 Re: Jets not working after fresh fill? It’s much like moving a piano – just have it moved and take it with you. SnA or SnB = This means that sensor A or sensor B is bad or has a poor connection to the circuit board.
Advanced Search Forum > Swimming Pool Care > Spas and Hot Tubs > Jets not working after fresh fill? You are a life saver. You could simply drain and refill and see if that solves your problem. I heard concerns that the impellor may be damaged so it doesnt push enough for all the jets but i would expect they would atleast bubble a little rather then not
Bob Hunt September 22, 2015 Reply Sundance Certa 2011 Jets pump 1 working erratically. If repeated attempts (hours apart) still cannot get pumps to prime, you can wait overnight and just let the spa sit. Apologies if this is already written up somewhere or misplaced. In Ground Spa Jets Not Working If the pump is on low, it won't be a disaster, just a little wet.
The heater now tries to kick on every so often for 4 seconds or so but then kicks off. The jets never really seemed to work great but they worked. My Hot Tub Won’t Heat Sometimes a heating problem is as simple as replacing a heater element, however sometimes the problem can be caused by another component. Ralph Sampson GFCI on a hot tub is not something to experiment with.
Sign in 52 10 Don't like this video? Bathtub Jets Not Working Solution: If hot tub is under-filled, add water to the normal fill line. What parts or scenarios would cause nothing to come on in this model?Thanks! This is something that is best left to the experts.
And about the heater and chasing the line to find the problem.
Jackie September 04, 2016 Reply Half of the jets are not working on my spa and then on one of the handles to turn the jets on or off sounds like Hot Tub Jets Not Working After Refill You should hear air or see water coming from it once it's loose. Hot Tub Jets Won't Turn On Whether you're draining and refilling in the middle of the season or filling up for the first time this winter, there's a good chance you're going to run into this problem.
Check that the cable is still intact and hasn't been severed by a rodent. Tip: Parts and labor from motor shops can be very close to the cost of a brand new pump with a warranty, so do yourself a favor and replace the pump Apologies if this is already written up somewhere or misplaced. If you ever have a question or concern about your hot tub, your guarantee, or any other issue you may have with your hot tub, you can email, or call Beachcomber Hot Tub Jets Weak
Do not allow children to climb on, sit or stand on your hot tub Heatshield. Apologies if this is already written up somewhere or misplaced. There could be a few things preventing your jets from pumping water. Why?
WATER CARE How do I take my FlexJets out? Spa Pump Not Working Thanks Reply With Quote 11-11-2012,11:52 AM #8 Tidbits View Profile View Forum Posts View Articles Join Date Nov 2012 Posts 3 Re: Jets not working after fresh fill? It has high and low speed.
Marie leopold Thank you…I have someone coming out Thursday so hopefully it will be something simple! Now Jet 1 is not working, but Jet 2 works fine. But it will be replaced as soon as April gets here. Hot Tub Air Lock Symptoms Copyright© 1995-2016 DoItYourself.com Inc.
I am going to suggest that this be added to the Pool School! Comments Topics: DIY basics outdoor living How to Apply Chlorine Shock to Your Hot Tub You may also like: How to Make a Cheap Hot Tub Cover Go for the inexpensive Then get to plunging on the hole that the filter threads onto or sits on. When the pump starts spraying water you will have to quickly tighten the coupling.
Hard Water A minor problem with jets in new tubs can be that the mobile jets become fixed. a perfectly working hot tub again! Marie leopold I just purchased an older hot tub from a friend. If it has, clean or change the filters.
Nigel May 15, 2016 Reply Scott check to see that the motor shaft is not stiff or stuck. If all else fails contact your local Spa Support Desk to book a diagnostic and repair of your Spa. If the filter just sits in a well behind a hole in the wall your life is much easier. Subscribe here.
Maybe it looks a little something like this: [attachment=0:12fija01]air relief.JPG[/attachment:12fija01] The red arrows point to unions, the blue arrow points to where there may or may not be a drain plug. A tip is to fill the spa from the filter canister with the hose instead of leaving the hose dangling in the foot well of the spa. This introduces water straight Repeat this process, using the lid like a plunger until water starts to come up at you from the filter housing. With a little luck, the next thing you hear will be bubbles coming from your jets followed by a fully primed pump.
I have a flo-master pump (230volt)(8.5amp)(1725/3450rpm). The noise happens when the thermostat seems to turn on and lasts for a few mins with this horrible noise then turns off. You can try and take the motor to a re-build shop but you might find a rebuild doesn't last as long as a new replacement. Planning for the hot tub'slocation in your yard Plan your hot tub location for the best privacy.
Brooke There seems to be a really loud noise coming from my heat element that with in the last few days is getting louder and louder. Pump 1 doesn't work still. Just enough to let some water or air out. Some spas may have a bleed valve, or some pumps may have one, but cracking the union and then re-tightening it is a quick way to purge the water if you