Please help! They have separate switches: 2 heat light switches, 1 light switch, and 1 fan switch. 3 of the heat lamps did not work for a while but one is still working. The electrical outlets in all 3 bathrooms work, just not the lights. That'd be my first troubleshooting step. Source
If the tester lights up, the socket is ok; if not, it could be a bad socket, a loose (or fried) wire en route to the socket, or a bad wall Ask an Expert Home Improvement Questions Electrical Questions How JustAnswer Works: Ask an Expert Experts are full of valuable knowledge and are ready to help with any question. You can only upload videos smaller than 600MB. Which 2 wires are you testing, and how are you testing them?
We did have the outside of the house power washed today in preparation of having the house exterior painted tomorrow. We have two low voltage lights with 11/8/2016 11/8/2016 green-owl We've had a lot of furnace repair lately. This morning I turn on the heat lamp and it started to flicker and makes funny noises.
One or more of the wires that lead to the bathroom lights may not have been connected as they were before. Bathroom light fixture(s) should be unfastened so the wiring and wire splice connections may be inspected. I recently had to rerun all the wiring in our bathroom vanity as all of the connections had corroded the wires away. Why Wont My Light Switch Work Light and outlets not working?
Side with two black screw says common on both. No Power In Bathroom Breaker Not Tripped The house is 14 years old and we have never had any electrical issues. I turn off the heat and use the light instead. http://www.doityourself.com/forum/electrical-ac-dc/503401-why-would-my-bathroom-light-switch-suddenly-stop-working-please-help.html Please see the page about Troubleshooting Electrical Wiring which may be helpful.
Get free quotes » 14 SHARES Philip Schmidt Philip Schmidt writes home improvement books. Lights Wont Turn On In One Room With a continuity checker (a multimeter is another great tool to have around the home, and not at all expensive) verify that when the switch is off, there should be essentially The lights suddenly quit working the other night, as well as the light over the shower - no power there or it's switch either. Another How To Channel 970,784 views 6:08 GFCI plugs, how to reset and test - Duration: 5:15.
I checked all breakers and non were kicked, i checked all breakers for continuity and voltage all tested fine, checked all gfi outlets in the house non were tripped but reset Why would my bathroom light switch suddenly stop working? Bathroom Light Not Working Bulb Ok Loading... Bathroom Vanity Light Not Working There may also be a bare copper or green wire connected to the switch for grounding purposes, in an old house this may be absent.
Checked the switch with a multimeter and it looks like it may be a power issue feeding the switch. this contact form I'm stumped…what do you think the problem could be? I hope this helps, Dave Tran says: December 9, 2014 at 3:52 am Hi my bathroom has four heat lamps with an exhaust fan and a light in the middle. They are panel lights so I am unable to test the lights elsewhere. Lights Wont Turn On Breaker Not Tripped
Related 3Why does the breaker trip occasionally after I installed a new light fixture?1Why is my bedroom light not working?1Why doesn't my replacement lighting work after my old fixture died?2Why are Forcing it with vise grips hasn't worked.6 points · 4 comments Need help fixing office chair8 points · 8 comments What's going on with our cabinet? You can try adding in the set of wires at the light, color for color. have a peek here permalinkembedsaveparentgive gold[–]aknal[S] 0 points1 point2 points 3 years ago(2 children)Simply on-off.
Believe it or not, I have been paid to discover that a customer's light bulb was burnt out, and one time the customer's light switch was in the off position - Changed Light Bulb Still Not Working If there is no label or panel schedule, and this is the only breaker that is tripped in the panel, AND when you tested the GFCI as written above and got You need to remove the wire nut and twist the wires and be sure all the copper is in contact on each one.AssuredElectrical : Be sure power is off, whites carry
I though you tested the wires?Customer: I tested the black wires leading to the switchCustomer: I haven't tested the white wires with the breaker on yet, I can do that if I changed out the old switch, wired it same way. KungFuMaintenance 556 views 4:46 Help! Ceiling Light Fixture Not Working Attention should focus on the wiring methods, and the electrical connections to each light fixture, as well as the switches.
I've checked and reset all breakers. If the GFCI does not reset then the GFCI outlet may need to be replaced. Dave Nick B says: July 12, 2013 at 2:51 am Last night i turned on the light switch in the bathroom, there was a huge blue spark/flash from where the lights Check This Out Chat Conversation StartedJason : Hello.
Wall switch and fixture cableBefore taking the fixture apart, you might as well check the wall switch and wire connections between the switch and fixture cable. They worked last night. permalinkembedsaveparentgive gold[–]dustingebhardt 0 points1 point2 points 3 years ago(3 children)Is the switch a dimmer-type, or a simple on/off-type? Sign in 4 16 Don't like this video?
If you cannot reach into the box with a voltage probe, then you will need to turn off the power into the switch box. Was a bit of a head-scratcher for me the first time it happened. Give it a small tug to make sure it's not going anywhere. Push the reset button.
If the circuit breaker is tripped the switch will be in the middle position. If it is dead too start looking for a tripped GFCI receptacle.