Home > Not Working > Basement Light Bulbs Not Working

Basement Light Bulbs Not Working

Contents

I changed the light bulbs only to realize that was not the problem. ReplyWas this helpful?Helpful? A windowless room contains three identical light fixtures, each containing an identical light bulb or light globe. There is still a current path but now it is through the other hot wire. Source

Light bulb blew and now no light bulbs will work in that socket? The voltage will depend on how evenly balanced the loads are on each hot leg.Have an electrician- confirm all neutral connections in your panel- confirm the neutral and ground are bonded Does 'noel' really have its origin in Latin? Sometimes the contact inside the socket can get bent, and prevents the bulb from properly making contact when screwed into the socket. http://www.networx.com/article/10-reasons-why-your-lights-dont-work

Ceiling Light Fixture Not Working

Assuming there is, then my guess is that a solder joint inside the fixture may have broken loose. Pull the fixture down, but keep your hands away from the wires. After you are off the ladder and have the fixture where you can comfortably check it you can now check for continuity. If there is voltage coming into the switch, but not going out of the switch (when it's on).

You can only upload videos smaller than 600MB. About Us Rooms Skills Parts of the House Outdoors Magazine Subscribe Give a Gift Advertise With Us Customer Care Content Submission Contact Us Privacy Policy Terms of Use SIGN UP FOR It's valid, but there are several reasons why this is not as good. Ceiling Light Stopped Working Never, never ever (did I say never) use a continuity tester on a live circuit.

If not you have a faulty socket. Copyright © 1995-2016 DoItYourself.com Inc. Answer This QuestionWas this helpful?Helpful? look at this site Nothing.I don't even know what to try next.

And as a side benefit, you two will spend some time together. Light Fixture Stopped Working Browse other questions tagged electrical bulb or ask your own question. That a loose or damaged neutral could be causing all these issues? CordBoth plug-in lamp cords and cords that tether hanging fixtures can come loose from the socket terminals, the internal fixture wiring, or the plug terminals.

Changed Light Bulb Still Not Working

If the wire ends are broken or corroded, strip off 3/4 in. It would not be uncommon to have all of the living room outlets on the same circuit, and you certainly couldn't run two space heaters on the same circuit. Ceiling Light Fixture Not Working Member benefits: Get a FREE Traditional Bookcase Project Plan Sign up for FREE DIY newsletters Join us Newsletters Shop DIY Books DIY Tip Genius App Free Product Info Promotions Login Join New Light Bulb Not Working Also removing the new one again doesn't help.

Or Login with Facebook Don't Have an account?Sign Up Today Cancel Search How-Tos Your Projects Forums search Hi Unregistered | Logout Connect with Facebook Login Sign Up Forum New Posts Today's http://giltronix.com/not-working/bathroom-light-not-working-uk-12v.html If so, check the cord connections. His published work includes material for major companies in the home improvement, plumbing, HVAC and power tool industry. Other rooms on the breaker had power. Lamp Not Working After Blown Bulb

If the tester lights up, the socket is ok; if not, it could be a bad socket, a loose (or fried) wire en route to the socket, or a bad wall electrical bulb share|improve this question edited Nov 28 '11 at 22:08 asked Nov 28 '11 at 17:21 bonifaz 123115 Did the light work with the single (unbroken) bulb, or It could be some sort of problem that will cause a fire. have a peek here It is a good idea to keep this list handy in case replacement or resetting the breaker is needed.

After talking on the phone and writing letters and reports at work, I always found it revitalizing to work with my hands in the shop in the evening. Light Wont Work Even With New Bulb If there are still no bells and whistles, you'll have to move to the switch to make sure it is functioning properly. You probably have two black wires and two white wires and maybe a ground.

What caused this to happen?

The fuse box is metal and may be located in a stairwell, closet, basement, or garage. US Election results 2016: What went wrong with prediction models? ReplyWas this helpful?Helpful? Lights Wont Turn On Breaker Not Tripped I replaced both the switches downstairs (not the one atop the stairs).

These can get pressed in so far that they no longer touch the bulb's electrical contact. [Editor's note: Really, remember to turn off the power to the outlet before you stick You need to flip it back firmly. Both bulbs were still good. Check This Out That is switch on 1&2, wait a minute, switch off two and go to the attic and check if the bulb is on, hot, or cold.

All outlets do not work and the ceiling light is not working. I guess they were installed with plans to use dimmer but that never happened. You might have to replace the cord, too, if the copper wiring is damaged.Pull-chain switches on mounted fixtures tend to fail before other parts. An apprentice family member just forgot to shut off main.

WARNING If at anytime during the procedure you see sparks, the breaker will not reset, or you just don't feel comfortable doing any of the steps, please contact an electrician. If you know how they switch, you can just temporarily hard wire them to see if the circuit works without the switches. I mean the thing that I can turn on or off to provide electricity for an entire room. Inspect the fixture for signs of arcing, or other damage.

Step 4: Restore power. Turn off the power to the fixture's circuit at the service panel, and remove the fixture and replace the switch with a matching part (provided you're familiar with basic wiring).6. Nothing. The summer months are an especially vulnerable time, with air conditioners going full blast for hours at a stretch, pushing electrical circuits to their limits.

Do not stick anything in an empty fuse socket, as this can trigger an electrical short, which could cause a serious injury or fatality. If it falls down while you’re replacing the fixture, wrap it in a circle and push it up as far into the electrical box as possible.

CAUTION! Socket tabIf a new bulb doesn't work, turn off the switch or pull the plug (turn off the power, that is), and try bending up the little, metal tab inside the Inspect the switch for signs of arcing, or other damage.

Nothing. These are easily distinguished from the common 110 volt breakers for lights and outlets.