Home > Bell Satellite > Bell Satellite 82 Not Working

Bell Satellite 82 Not Working

Contents

The guy visiting will now know to look at that as well. I believe that the manual says to do this. the noise was really high pitched, I could barely hear it, she could, and so could my sister, a few dog jokes ensued. This is what my guy had.. Check This Out

Weird thing.. I want to contact the people and ask them some questions. again, make sure you talk to tech 3. What can i do?

How To Find Bell Satellite 82 From 91

When I go to the dish signal strength page under the nimiq 82, it says (in red) wrong sat - 91. One Bill Mobility Bill Close Select your Satellite TV receiver The model number can be found on the front of your receiver in the bottom right corner. rybo10-25-2007, 02:26 PMSo how is the HDTV? :) berbs10-25-2007, 06:22 PMSo how is the HDTV? :) I got the 82 now....and no dice on the 91...so I got HD channels and

Is this because the dish is not at the right angle, or is the switch not functioning? The Dishnet sat's are actually harder to fine tune where you are then then the Expressvu one's. Vulcan View Public Profile Send a private message to Vulcan Find More Posts by Vulcan 07-28-2009, 08:58 AM #9 Wookie Chick Magnet Join Date: Oct 2001 Exp: Okay, thanks Bell Satellite No Signal 015 Next step for troubleshooting, take one of the "two" wires going into the switch, and connect it directly into the "one" on the other side of the switch.

Olympics Sponsored Forums Realtor 1 Real Estate Gem by Carati Mortgage. Bell Satellite 82 Or 91 Took him about 2 minutes.. I can then usually switch back to the SD channel. This Site Password Register Forum Rules FAQ Community Calendar Today's Posts Search Notices Due to recent reports of problems receiving emails, CP has switched to a new method of delivering emails.

Is this because the dish is not at the right angle, or is the switch not functioning? Bell Satellite 82 Channels When I try to get a feed on my receiver, it only picks up the Nimiq 91 sat. I"M in california, and having trouble getting BOTH birds. One Bill Mobility Bill Close Select your Satellite TV receiver The model number can be found on the front of your receiver in the bottom right corner.

Bell Satellite 82 Or 91

The most common causes of complete loss of signal are either a bad connection, or no power to the switch. http://support.bell.ca/TV/Receivers/My_TV_is_showing_Error_015_Acquiring_satellite_signal once i get a good signal with the 91 I connect the 82 lnb into the switch and run a check switch. How To Find Bell Satellite 82 From 91 if problem stays in same location you know its the cabling. Can't Find Bell Satellite 91 Here's a real good forum for help with this if you're still having problems.

If not and If the line was good on my sat finder, I would recommend that you switch to Shaw. his comment is here berbs10-24-2007, 02:42 PMWhen the signal says that it is connecting with the wrong satellite then you likely have the dish at the wrong pitch. I wound up doing that when I was subbed with Bell. berbs10-24-2007, 05:45 PMYes. Bell Satellite 91 No Signal

You must have 2 and they must be connected to the SW21 switch. The signal strength is the same as the nimiq 91, but is in red. The signal strength is the same as the nimiq 91, but is in red. this contact form Did a bit of elevation & azim tuning to get best signal on 91, and next check in on 82.

Beels10-24-2007, 04:00 PMthanks..I;ll read it asap...this is pissing me off big time. Bell Satellite 91 Transponder Captain SK10-26-2007, 02:38 PMIt should take the sat guy a minimal amount of time to hit both Expressvu Birds for you. back up and running.

Colin #7 cashguru, Nov 29, 2004 gmalNew MemberJoined:Jan 4, 2005Posts:2Likes Received:0Location:Toronto I am having the exact same problem; I have been troubleshooting this, did a direct LNB cable test - the

Cool - thanks. ask to talk to the tech 3 level and let them know what happened. Join us! How To Find Nimiq 91 And 82 MY guess, the cables from the dish to the switch and the LNBs are okay, or else you'd still get at least one satellite.

Everything you do here at SatelliteGuys costs us money, as we have to pay for the bandwidth you use, plus expenses such as upkeep of our servers and software licenses.We ask You would probably get a new HD Shaw receiver & Dish installed for "net" free, or a new PVR that puts you out maybe $50 if current promotions continue. It just hooks in between the LNB and coax to the receiver and you can set the gain on it for extreme fine tuning. navigate here If the weather is not the issue, check the following: Loose/missing connections: Check that the cable coming from the satellite dish is connected to Satellite In on the back of your

I skewed the heck out of the dish, but still nothing for 82. Any suggestions? That is ridiculous especially if you got one of their techs to initially install it. Newer Than: Search this thread only Search this forum only Display results as threads Useful Searches Recent Posts More...

I would have never found that. Glad you didn't have to pay. Call us at 1 866 797-8686 Other ways to contact us BackBack My TV is showing Error 015: Please standby for the satellite signal Error 015:  Please standby for the satellite Submit Related Articles Bell Satellite TV Error 002: Your satellite signal is temporarily unavailableMy Bell Satellite TV signal fluctuatesMy TV is showing Error 005 (SmartCard authorization error)I can’t access a

US or Canada? If so this image may help you. RILEYSROMPERS10-25-2007, 10:16 PMI got the 82 now....and no dice on the 91...so I got HD channels and thats it...